VandlGuard® One Anti-Graffiti Coating
Protects surfaces from damage caused by graffiti
Sustains repeated graffiti removals for 1 year. Non-Sacrificial – remove graffiti without impacting protective layer.
Preserves the look of the building with a natural permeable finish and will not yellow.
Safe to use
Can be applied anywhere in North America because it contains Zero VOC, no carcinogens, no odor and can be applied on exterior surfaces and interior OEM environments.
Easy to apply
With a flood coat. Fast dry time and cure time. Warranty up to 1 year.
VandlGuard® One Anti-Graffiti Coating
VandlGuard® One Anti-Graffiti Coating is a non-sacrificial anti-graffiti coating that protects surfaces from permanent staining and damage caused by commercially available spray paints. The coating can be applied to any vertical or horizontal exterior surface and dries clear (will not yellow). VandlGuard® One is eligible for a 1 year material & labor warranty.
|Note to Specifier – CSI Reference Codes|
|09 96 23||GRAFFITI RESISTANT COATINGS|
Best Tools for Application
A foam brush is recommended to soak in and saturate your substrate.
Use a small hand pump sprayer.
Use an airless sprayer with a spray tip size between .035mm to .051mm.
Application Best Practices
1) Step One: Prepare the surface and confirm surface moisture is less than 25%. Remove dirt, grime, efflorescence, lime run, construction debris, form oils and release agents, chalked materials, loose and peeling paint, mold, mildew, etc. All cracks should be pointed or caulked.
2) Step Two: Perform a test application to confirm fit and finish.
3) Step Three: Apply the product according to It’s TDS.
4) Step Four: Let cure.
5) Step Five: Perform post application test to assure results are achieved.
Benefits of Concentrates and How to Mix
- Reduces carbon footprint
- Reduces job site and landfill waste
- Reduces worker and supply chain fatigue
- Refer to the description on the packaging for dilution ratios.
- Pour contents of concentrate into an empty container. The container size should be the size of the finished amount of product.
- Fill the container with clean water – we recommend distilled water for best results.
- Mix lightly with a stir stick.
Specification and Ordering Options
Substrate Uses and Anticipated Coverage Rates
Substrate porosity varies due to type of substrate and/or the age of the surface and its exposure to weathering. As a result, coverage rates may also vary. In addition, in certain applications, two coats may be required. Please contact us for coverage estimates. Best practices are to first perform a test application on the substrate, followed by a rilem tube test to ensure adequate coverage/absorption.
Refer to the product TDS for Surface Preparation and Application Methods.
Need help? Call 1-888-765-7070 Option 2.
|Substrate||Sq Ft / Gallon||# Of Coats|
|Precision/Split Face Block||200||1|
|Ground Face Block||200||1|
|Sand Blasted Block||180||1|
|Heavy Textured Stucco||200||1|
|Fine/Medium Textured Stucco||250||1|
|Sand Blasted Concrete||225||1|
Testing Data and Product Characteristics
|ASTM C666||2200 Cycles – No effect|
|ASTM C672||100 Cycles No Mass Loss, No Scaling|
|ASTM D2243||Do Not Freeze|
|ASTM G154||2,500 Hours No Loss in Repellency|
|ASTM C672/M||100 Cycles Treated Concrete, No Scaling|
|ASTM E-514||98.7% Leak Red Water Pen Fed Spec|
|SS-W-110C, ASTM C140||75% Min Required, 96.8% Leak Reduction|
|ASTM D-1653||98.6% Effective|
|ASTM C67||100% Vapor Permeable|
|ASTM G||98.6% Effective|
|ASTM E84||3,500 Hours- No Change|
|NCHRP No. 244||95% Reduction, Series IV Salt Pounding
87% Reduction, Series II Salt Pounding
87% Reduction, Series II Chloride Ion Absorption
|Silane/Siloxane||Active Content 100%|
|Color of Material||Milky White|
|V.O.C.||0 g/L V.O.C. Compliant in North America|
|Viscosity||9.6 Seconds No. 4 Ford Cup|
|Weight||Approximately 8.7 lbs./Gal.|
|Surface Dry/Recoat/Usable||Approximately 1 Hour|
|Coalescence Cure Time||5 to 7 days|
Approvals, Qualifications and Associations
Call 1-888-765-7070 Option 2 for additional assistance.
|LAUSD – OESH||Approved|
|LEED Points||Up to 3 Points|
|LEED (New Construction)||Available|
|LEED (New Schools/CHPS)||Available|
|All Other States and Canada||Compliant|
|HPD||Various Products Approved|
|American Institute of Architecture||Two Approved CE courses|
Data Sheets & Other Document Download
| TECHNICAL DATA SHEET | SAFETY DATA SHEET | ARCHITECTURAL SPECIFICATIONS | LARR APPROVAL REPORT | FIELD INSPECTION REPORT | LEED CREDITSHPD CERTIFICATION | WARRANTY PRE-REGISTRATION