
Blok-Lok w/ Graffiti Control Water Repellent / Anti-Graffiti
Hybrid water repellent / anti-graffiti solution
Non-Sacrificial – remove graffiti without impacting protective layer.
Natural Finish
Preserves the look of the surface and will not yellow.
Safe to use
Can be applied on interior or exterior vertical surfaces.
Easy to apply
With a flood coat, no masking or taping required and clean up with only soap and water. Warranty up to 5 years.
Blok-Lok w/ Graffiti Control Water Repellent / Anti-Graffiti
BLOK-LOK™ with Graffiti Control is a hybrid water repellent and anti-graffiti solution. The formula penetrates deep to seals vertical porous substrates and create a non-sacrificial anti-graffiti barrier. After two coats are applied, graffiti can be easily removed with VANDLCLEAN SUPER.
Blok-Lok™ with Graffiti Control provides Professional grade, heavy-duty graffiti and water repellent performance on a wide variety of vertical surfaces including:
- Bare Wood
- Brick
- Concrete
- EFIS or Cement Plaster
- Masonry Block
- Stucco
- Porous Stone
- Unglazed Tile
Note to Specifier – CSI Reference Codes | |
07 19 00 | Acrylic, Silane Siloxane, Penetrating Polyester, Hybrid Water Repellents |
09 96 23 | GRAFFITI RESISTANT COATINGS |


Best Tools for Application
Small Surfaces
A foam brush is recommended to soak in and saturate your substrate.
Medium Surfaces
Use a small hand pump sprayer.
Large Surfaces
Use an airless sprayer with a spray tip size between .035mm to .051mm.
Application Best Practices
1) Step One: Prepare the surface and confirm surface moisture is less than 25%. Remove dirt, grime, efflorescence, lime run, construction debris, form oils and release agents, chalked materials, loose and peeling paint, mold, mildew, etc. All cracks should be pointed or caulked.
2) Step Two: Perform a test application to confirm fit and finish.
3) Step Three: Apply the product according to It’s TDS.
4) Step Four: Let cure.
5) Step Five: Perform post application test to assure results are achieved.


Benefits of Concentrates and How to Mix
- Reduces carbon footprint
- Reduces job site and landfill waste
- Reduces worker and supply chain fatigue
- Refer to the description on the packaging for dilution ratios.
- Pour contents of concentrate into an empty container. The container size should be the size of the finished amount of product.
- Fill the container with clean water – we recommend distilled water for best results.
- Mix lightly with a stir stick.
Specification and Ordering Options
Substrate Uses and Anticipated Coverage Rates
Substrate porosity varies due to type of substrate and/or the age of the surface and its exposure to weathering. As a result, coverage rates may also vary. In addition, in certain applications, two coats may be required. Please contact us for coverage estimates. Best practices are to first perform a test application on the substrate, followed by a rilem tube test to ensure adequate coverage/absorption.
Refer to the product TDS for Surface Preparation and Application Methods.
Need help? Call 1-888-765-7070 Option 2.
Coverage Rates
Substrate | Sq Ft / Gallon | # Of Coats* |
CMU Block | 60-80 | 2 |
Clay Brick | 125-150 | 2 |
Stucco | 100-150 | 2 |
Dense Masonry Surfaces | 125-150 | 2 |
Wood | 150-200 | 2 |
Clay Block | 50-60 | 2 |
EFIS | 80-120 | 2 |
Testing Data and Product Characteristics
Testing Data
Wind Driven Rain | ASTM E-514-86., 98.7% Leak Red |
Water Pen Fed Spec | SS-W-110C, 75% Min Req, 96.8 Leak Red Chloride Ion Intr |
Salt Pounding NCHRP | No. 244 Series IV – 95% Red, No. 244 Series II – 83% Red |
Water Abs CMU ASTM C140-75 | 98.6% Effective |
Water Vapor Trans ASTM D-1653-71 | 100% Vapor Perm |
Water Repellency ASTM C67-87 | 98.6% Effective |
Weathering ASTM G-53 | 3,500 Hours – No Change |
Maximum Scrubbing Cycles | 35 |
ASTM D6578 | Level 2 |
Product Characteristics
Material | Silane/Siloxane |
Active Content | 100% |
Volume Solids | 4% |
Color of Material | Milky White |
Odor | Slight Odor |
V.O.C. | 20 g/L V.O.C. Compliant in North America |
Flash Point | Non-Flammable |
pH Value | 6 |
Viscosity | 9.6 Seconds No. 4 Ford Cup |
Weight | Approximately 8.7 lbs./Gal. |
Surface Dry/Recoat/Usable | Approximately 1 Hour |
Coalescence Cure Time | 5 to 7 days |
Approvals, Qualifications and Associations
Call 1-888-765-7070 Option 2 for additional assistance.
LAUSD – OESH | Approved |
LEED Points | Up to 3 Points |
LEED (New Construction) | Available |
LEED (New Schools/CHPS) | Available |
CARB | Compliant |
SCAQMD | Compliant |
All Other States and Canada | Compliant |
FDA | Meets Requirements |
USGBC | Member |
APTA | Member |
HPD | Various Products Approved |
American Institute of Architecture | Two Approved CE courses |