VandlGuard® Ten Anti-Graffiti Coating
Protects surfaces from damage caused by graffiti
Sustains repeated graffiti removals for 10 years. Non-Sacrificial – remove graffiti without impacting protective layer
Natural Finish
Preserves the look of the building with a natural permeable finish and will not yellow.
Safe to use
Can be applied anywhere in North America because it contains Zero VOC, no carcinogens, no odor and can be applied on exterior surfaces and interior OEM environments.
Easy to apply
With a flood coat. Fast dry time and cure time. Warranty up to 10 years with Finish Coat.
VandlGuard® Ten Anti-Graffiti Coating
VandlGuard® Ten Anti-Graffiti Coating is a part of a two step non-sacrificial anti-graffiti coating that protects surfaces from permanent staining and damage caused by commercially available spray paints. Used in conjunction with VandlGuard® Finish, the coating can be applied to any vertical or horizontal exterior surface and dries clear (will not yellow). VandlGuard® Ten is eligible for a 10 year material & labor warranty (see TDS for details).
| Note to Specifier – CSI Reference Codes | |
| 09 96 23 | GRAFFITI RESISTANT COATINGS |
Best Tools for Application
Small Surfaces
A foam brush is recommended to soak in and saturate your substrate.
Medium Surfaces
Use a small hand pump sprayer.
Large Surfaces
Use an airless sprayer with a spray tip size between .035mm to .051mm.
Application Best Practices
1) Step One: Prepare the surface and confirm surface moisture is less than 25%. Remove dirt, grime, efflorescence, lime run, construction debris, form oils and release agents, chalked materials, loose and peeling paint, mold, mildew, etc. All cracks should be pointed or caulked.
2) Step Two: Perform a test application to confirm fit and finish.
3) Step Three: Apply the product according to It’s TDS.
4) Step Four: Let cure.
5) Step Five: Perform post application test to assure results are achieved.
Benefits of Concentrates and How to Mix
- Reduces carbon footprint
- Reduces job site and landfill waste
- Reduces worker and supply chain fatigue
- Refer to the description on the packaging for dilution ratios.
- Pour contents of concentrate into an empty container. The container size should be the size of the finished amount of product.
- Fill the container with clean water – we recommend distilled water for best results.
- Mix lightly with a stir stick.
Specification and Ordering Options
Substrate Uses and Anticipated Coverage Rates
Substrate porosity varies due to type of substrate and/or the age of the surface and its exposure to weathering. As a result, coverage rates may also vary. In addition, in certain applications, two coats may be required. Please contact us for coverage estimates. Best practices are to first perform a test application on the substrate, followed by a rilem tube test to ensure adequate coverage/absorption.
Refer to the product TDS for Surface Preparation and Application Methods.
Need help? Call 1-888-765-7070 Option 2.
| Substrate | Sq Ft / Gallon | # Of Coats* |
| Precision/Split Face Block | 200 | 1 |
| Ground Face Block | 200 | 1 |
| Scored/Fluted Block | 180 | 1 |
| Sand Blasted Block | 180 | 1 |
| Slump/Adobe Block | 200 | 1 |
| Heavy Textured Stucco | 200 | 1 |
| Brick | 250 | 1 |
| Unpainted Wood | 200 | 1 |
| Porous Tile | 200 | 1 |
| Fine/Medium Textured Stucco | 250 | 1 |
| Cast/Pre-Cast/Tilt-Up Concrete | 250 | 1 |
| Sand Blasted Concrete | 225 | 1 |
*DOES NOT INCLUDE NUMBER OF COATS OF VANDLGUARD FINISH COAT. This is just the number of coats of VandlGuard Five.
Testing Data and Product Characteristics
Testing Data
| ASTM C666 | 2200 Cycles – No effect |
| ASTM C672 | 100 Cycles No Mass Loss, No Scaling |
| ASTM D2243 | Do Not Freeze |
| ASTM G154 | 2,500 Hours No Loss in Repellency |
| ASTM C672/M | 100 Cycles Treated Concrete, No Scaling |
| ASTM E-514 | 98.7% Leak Red Water Pen Fed Spec |
| SS-W-110C, ASTM C140 | 75% Min Required, 96.8% Leak Reduction |
| ASTM D-1653 | 98.6% Effective |
| ASTM C67 | 100% Vapor Permeable |
| ASTM G | 98.6% Effective |
| ASTM E84 | 3,500 Hours- No Change |
| NCHRP No. 244 | 95% Reduction, Series IV Salt Pounding 87% Reduction, Series II Salt Pounding 87% Reduction, Series II Chloride Ion Absorption |
Product Characteristics
| Silane/Siloxane | Active Content 100% |
| Reactive Solids | 40% |
| Volume Solids | 4% |
| Color of Material | Milky White |
| Odor | Slight Odor |
| V.O.C. | 0 g/L V.O.C. Compliant in North America |
| Flash Point | Non-Flammable |
| pH Value | 6 |
| Viscosity | 9.6 Seconds No. 4 Ford Cup |
| Weight | Approximately 8.7 lbs./Gal. |
| Surface Dry/Recoat/Usable | Approximately 1 Hour |
| Coalescence Cure Time | 5 to 7 days |
Approvals, Qualifications and Associations
Call 1-888-765-7070 Option 2 for additional assistance.
| LAUSD – OESH | Approved |
| LEED Points | Up to 3 Points |
| LEED (New Construction) | Available |
| LEED (New Schools/CHPS) | Available |
| CARB | Compliant |
| SCAQMD | Compliant |
| All Other States and Canada | Compliant |
| FDA | Meets Requirements |
| USGBC | Member |
| APTA | Member |
| HPD | Various Products Approved |
| American Institute of Architecture | Two Approved CE courses |